How to Install Vertical Blinds

For decades the vertical blind was practically solely used in office buildings, however as our tastes in house décor progressively ended up being more varied, different styles of vertical blinds were launched to the market.

Whether you are remodelling a new house or simply sprucing up a particular room, your choice of window coverings varies from easy drapes to futuristic, programmable glass, and everything in between.

A great deal of us shy away from selecting vertical blinds due to being worried that the installation procedure will be overly complicated and time-consuming. Setting up vertical blinds appropriately is not as tough as you might believe, and with this guide, we aim to make the procedure even simpler.

Tools you need

  • Pencil
  • Tape measure
  • Electric drill + bits
  • Screwdriver
  • Screws
  • Blinds
  • A helper
  • Ladders/ stepladders

Pre-installation preparation
No matter which type of vertical blinds you would like, inside or outside install, the first thing you need to do is determine the window so that you understand the size of blinds you require to purchase.

To make sure that the blinds fit properly, you should initially measure from below the window at the point where you would like the blinds to hang. From that point, measure the height to the location where the headrail will be set up.

How to set up vertical blinds– inside install
Open the blinds’ product packaging, read the guidelines, and ensure you have all of the essential parts.
Lay the valance on a flat surface area and location the brackets on it 7.6 cm (3 inches) from each end.
Using a pencil, mark the screw holes for each bracket.
Drill the screw holes, if possible use a drill bit which is smaller sized than the screws.
Mark the position of the brackets with your pencil on the window frame. The brackets must be 7.6 cm (3 inches) far from the outdoors edge and 2,5 cm (1 inch) away from the glass.
Hold the bracket in position, position a screw in the hole and tap it with a hammer. Repeat this up until you have actually marked the positions of all 4 screws.
Have your helper hold the valance in place, make certain that the pre-drilled holes compare with the pre-marked locations.
Connect the very first bracket and repeat for the 2nd.
Connect the headrail, most of blinds have a headrail which merely snaps into place. Describe the item guidelines for the correct setup treatment.
Attach the vanes. If you are not sure on how to do this there will be a different section below describing the procedure.

How to install vertical blinds– outside install.
Open the blinds’ product packaging, read the directions, and ensure you have all of the needed elements.
Find where the headrail will be installed, pick a location at the bottom of the window, ideally the centre, and procedure from where you desire the blinds to stop to the top of the window and mark it with your pencil.
Position the headrail straight on top of the pencil mark and have your assistant hold it in place.
Measure 10cm (4 inches) from the edge of the window and make a pencil mark above the headrail, repeat on the other side.
Eliminate the headrail and attach the brackets to the wall, for additional stability pre-drill the holes and insert wall anchors for the screws.

Get the ideal spacing, pull the cord until all of the vanes clips are an equal distance from one another.
Turn the vane clips so that the slit is dealing with towards you.
Connect the vanes. At one end of each vane, there is a hole, push that end into the vane slit up until the hole is caught by the hook inside the clip.
Repeat this for the remainder of the vanes.

How to preserve your vertical blinds?
After the setup, add cleaning up the blinds to your list of weekly chores to make maintenance easier, this will also decrease the need for a thorough cleaning.

Using the brush accessory, vacuum the blinds starting from the leading and work your way down. Washing vertical blinds can be a little bit tricky as most types can not be machine washed and getting rid of each vane can be a trouble. For a basic yet reliable cleaning approach see below.

You will need:

  • One container of warm, soapy water;
  • One pail of clean, cold water;
  • Old towels or a tarp;
  • A blind cleaning tool.
  • How to make your own tools?
  • Get a set of barbecue tongs and one sponge.
  • Cut the sponge in half.
  • Glue each half sponge to the ends of the tongs with waterproof glue.
  • Allow the glue to dry over night.

How to clean up the blinds?


  • Place the old towels, or tarpaulin, below the blinds to protect the flooring from drips.
  • Dip the tongs in the warm, soapy water up until the sponges are filled.
  • Starting from the top, position the vane between the tongs so that there is a sponge on each side.
  • Press the tongs together and wipe down towards the bottom of the vane.
  • Rinse the sponges in the clean water.
  • Repeat until each vane is tidy.
  • Get rid of any excess water by gently patting the vanes with a towel.
  • Permit them to air dry.
    So there we have it, your guide on how to set up vertical blinds properly. With a bit of preparation, an assistant, and this guide you’ll have your brand-new blinds installed in no time.

Post Sponsored by